ESP8266 I/O Adapter + ESP-12E © androegg
ESP8266 I/O Adapter incl. 2 pcs. 8 pin pin header
ESP8266 ESP-12S with Resistors
|
|
Das ESP-12 Set ist wie folgt verfügbar:
Die ESP-12 Set wurden für den Einstieg ins Internet of Things zusammengestellt.
- GPIO 0 zum Flashen über den enthaltenen 10kΩ Widerstand auf GND
- RST zum Reset des ESP-12F über einen 10kΩ Widerstand auf GND
herstellen.
Der ESP-12 kann dabei sowohl mit
- der original Espressif
- NodeMCU / Lua
- Micropython
- Espruino
- …
Firmware betrieben werden.
IoT ESP-12 mit 32Mbit Set
Die typischerweise benötigten 10KΩ Widerstände zum Betrieb, bzw. Flashen sind im Lieferumfang enthalten. |
ESP8266 ESP-12 Set available:
The ESP8266 ESP-12 Set includes everything to operate an ESP-12 Module, simply connect
- VCC / GND for ESP-12 power supply
- CH_PD for enabling ESP-12 Module
- RX / TX for serial data transfer to USB TTL Converter
- GPIO 0 to GND over 10kΩ Resitistor (included) for flashing ESP-12 Module
- connect RST to GND thru 10kΩ Resitistor (included) to reset ESP-12 Module
With 32Mbit Flash the AI Thinker ESP-12F Module is able running
- original Espressif
- NodeMCU / Lua
- Microphyton
- Espruino
Firmware.
ESP8266 ESP-12 32Mbit set
The required 10KΩ Resistors are included. |
ESP-12E Features:
- CPU / MPU:
- Frequency: 80 / 160 MHz.
- Risk: 32-bit
- Instruction Ram: 64 Kb
- Data Ram: 96 Kb
- SPI Flash:
- Flash memory: 32Mb
- clock frequency: 75 MHz.
- Page program: up to 256 bytes in 0.64ms (TYP)
Sector erase: 512Kb in 0.6s
- Bulk erase: 17 – 23 s
- Hardware write protection: protected area size defined by nonvolatile bits BP0, BP1, BP2
- Deep power-down: 1μA (TYP)
- Write Cycles: > 100,000 write cycles per sector
Data retention: > 20 Years
- 802.11 b/g/n protocol
- supports Wi-Fi Direct (P2P)
- soft-AP Integrated TCP/IP protocol stack
- integrated PCB Antenna
- +19.5 dBm output power in 802.11b mode
- Power down leakage current of < 10uA
- Integrated low power 32-bit MCU
- supported Interface
- SDIO 2.0
- SPI
- UART
- STBC
- MIMO
- A-MPDU & A-MSDU aggregation & 0.4μs guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
I/O Adapter Features
- 16 soldering points 2mm Pitch
- 2 piece 2.54 mm 8 Pin Strip
- 16 pre-tinned Pins
- ESP-07 support
- ESP-07S support
- ESP-08 support
- ESP-12 support
- ESP-12S support
- ESP-12E support ¹
- ESP-12F support ¹
- ESP-14 support ¹
¹ only 16 standard Pins, the 6 extended Pins are not supported
|