ESP32-S3 N16R8 OV2640 CAM Module Set © androegg
![](https://www.androegg.de/wp-content/uploads/2024/06/ESP32-S3-OV2640-Camera-Modul-Set-kompl.jpg)
ESP32-S3 N16R8 OV2640 CAM Module Set 8MB PSRAM Bluetooth 5.0 © androegg
![](https://www.androegg.de/wp-content/uploads/2024/06/ESP32-S3-OV2640-Camera-Modul-Set-Borad-top.jpg)
ESP32-S3 N16R8 OV2640 WiFi CAM Module Set 16MB Flash © androegg
![](https://www.androegg.de/wp-content/uploads/2024/06/ESP32-S3-OV2640-Camera-Modul-Set-detail.jpg)
|
|
Das ESP32-S3 OV2640 Camera Modul Set beinhaltet:
- 1 Stück ESP32-S3 Kamera Modul mit integriertem SD Kartenleser
- 1 Stück OV2640 Kamera Modul
- 2 Stück Pinleiste
Das ESP32-S3 OV2640 Camera Board verfügt über
- Boot / GPIO0 Taster
- Chip Enable / Reset Taster
- Power ON Status LED
- IO2 Status LED
- UART RX und TX Status LED
- SK6812 RGB LED / GPIO48
- 2 USB-C Schnittstellen
- 1 x USB OTG
- 1 x UART zur seriellen Kommunikation
- CH340 USB TTL Konverter
- AMS1117 Spannungskonverter 3,3V
- Micro SD SPI Kartenleser (GPIO 38, GPIO 39, GPIO 40)
- OV2640 Kamera Modul Anschluss (GPIO 4, 5, 6, 7, 8, 9, 10 , 11, 12, 13, 15, 16, 17, 18)
- MSM261S4030HOR I2S Audio Schnittstelle
Der OV2640-Bildsensor ist ein ultra kompakter Bildsensor mit optimierten Energieverbrauch. Das OV2640 Kamera Modul erfüllt alle Funktionen einer einzelnen UXGA-Kamera / Bildprozessors.
Die SCCB-Bussteuerung erlaubt 10-Bit-Sampling sodass verschiedene Auflösungen individuell konfiguriert werden können.. Gleichermassen können
- Bildqualität
- Datenformat
- Übertragung
- Gammakurve
- Weißabgleich
- Sättigung
- Chrominanz
- Ausgabeformat RGB565 / JPEG / YUV / YCbCr
- usw.
individuell konfiguriert werden. Bitte beachten vorgenannte Parameter stehen selbstredend in Abhängigkeit der jeweilig verwendeten Firmware / Bibliothek.
ESP32-S3 Modul basiert auf dem Espressif Xtensa dual core LX7 Microprozessor mit 8MB PSRAM (GPIO 35, 36, 37) und 16MB Flash.
Das ESP32-S3 eignet sich für
- Espressif ESP-IDF SDK
- Python
- Python Thonny
- CircuitPython
- Espressif IDF
- Arduino (Espressif ESP32 Arduino Core 2.0.3 und höher)
- Tasmota (tasmota32s3- binaries)
Die ESP32-S3 LX7 Xtensa® Dual Core 32bit MCU erreicht bis zu 240MHz.
ESP32-S3 N16R8 Modul
Das ESP32-S3 Modul unterstützt
- 802.11 b/g/n Standard
- HT40 WLan Transceiver
- Bluetooth bis 5.0
- Taktfrequenz 240MHz
- SRAM 512kBytes
- 8 MB PSRAM
- 16 MB Flash
- bis zu 45 GPIO
- unterstützte Schnittstellen
SPI SD Karte,
UART,
SPI,
SDIO,
I2C,
LED PWM,
Motor PWM,
I2S,
IR,
pulse counter,
GPIO, capacitive touch sensor,
ADC 12-bit (bis zu 20 Kanäle),
DAC,
Two-Wire Automotive Interface (TWAI®), compatible with ISO11898-1 (CAN Specification 2.0)
|
The ESP32-S3 OV2640 Camera Module Set includes:
- 1 piece ESP32-S3 camera module with integrated SD card reader
- 1 piece OV2640 camera module
- 2 pieces pin strip
The ESP32-S3 OV2640 Camera Board features
- Boot / GPIO0 button
- Chip enable/reset button
- Power ON status LED
- IO2 status LED
- UART RX and TX status LED
- SK6812 RGB LED/GPIO48
- 2 USB-C interfaces
- 1 x USB OTG
- 1 x UART for serial communication
- CH340 USB TTL converter
- AMS1117 voltage converter 3.3V
- Micro SD SPI card reader (GPIO 38, GPIO 39, GPIO 40)
- OV2640 camera module connector (GPIO 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 15, 16, 17, 18)
- MSM261S4030HOR I2S Audio Interface
The OV2640 image sensor is an ultra compact image sensor with optimized energy consumption. The OV2640 camera module fulfills all the functions of a single UXGA camera / image processor.
The SCCB bus control allows 10-bit sampling so that different resolutions can be individually configured
- picture quality
- Data format
- transmission
- Gamma curve
- White balance
- saturation
- Chrominance
- Output format RGB565 / JPEG / YUV / YCbCr
- etc.
can be configured individually.
Please note the above mentioned parameters are of course dependent on the respective firmware/library used.
ESP32-S3 Module based on Espressif dual core LX7 MCU with 8MB PSRAM(GPIO 35, 36, 37) .
The ESP32-S3 Developmnet Baord supports
- Espressif ESP-IDF SDK
- Python
- Python Thonny
- CircuitPython
- Espressif IDF
- Arduino (Espressif ESP32 Arduino Core 2.0.3 and later)
- Tasmota (tasmota32s3- binaries)
The ESP32-S3 LX7 Xtensa® Dual Core 32bit MCU supports up to 240 MHz.
ESP32-S3 N16R8 Modul
The ESP32-S3 Module supports
- 802.11 b/g/n Standard
- HT40 WLan Transceiver
- Bluetooth up to 5.0
- Frequency 240MHz
- SRAM 512kBytes
- 8MB PSARM
- up to 45 GPIO
- supported Interfaces
SPI SD Karte,
UART,
SPI,
SDIO,
I2C,
LED PWM,
Motor PWM,
I2S,
IR,
pulse counter,
GPIO, capacitive touch sensor,
ADC 12-bit (up to 20 channels),
DAC,
Two-Wire Automotive Interface (TWAI®), compatible with ISO11898-1 (CAN Specification 2.0)
|
ESP32-S32 N16R8 OV2640 CAM Module Features:
- Power Supply: 5V
- I2S Audio Interface: MSM261S4030HOR
- Boot / GPIO0 button
- Chip enable/reset button
- Power ON status LED
- IO2 status LED
- UART RX and TX status LED
- SK6812 RGB LED/GPIO48
- Dual USB-C
- 1 x USB OTG
- 1 x UART for serial communication
- CH343 USB TTL converter
- AMS1117 voltage converter 3.3V
- Micro SD SPI card reader (GPIO 38, GPIO 39, GPIO 40)
- OV2640 camera module connector (GPIO 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 15, 16, 17, 18)
ESP32-S32 N16R8 Features:
- CPU / MPU:
Frequency: up to 240 MHz. based on Xtensa LX7
448 KByte ROM size
520 KByte SRAM size
8MB PSRAM
- 802.11 b/g/n/e/i protocol
- supports Wi-Fi Direct (P2P)
- soft-AP Integrated TCP/IP protocol stack
- 802.11 n (2.4 GHz), up to 150 Mbps
- 802.11 e: QoS for wireless multimedia technology
- Block ACK
- Fragmentation and defragmentation
- Automatic Beacon monitoring/scanning
- 802.11 i security features: pre-authentication and TSN
- Wi-Fi Protected Access (WPA)/WPA2/WPA2-Enterprise/Wi-Fi Protected Setup (WPS)
- Infrastructure BSS Station mode/SoftAP mode Wi-Fi Direct (P2P), P2P Discovery, P2P Group Owner mode and P2P Power Management
- UMA compliant and certified
- Antenna diversity and selection
- Compliant with Bluetooth v4.2 BR/EDR and BLE specification
- deep sleep current of < 2.5uA
- Class-1, class-2 and class-3 transmitter without external power amplifier
- Enhanced power control
- +10 dBm transmitting power
- NZIF receiver with -98 dBm sensitivity
- Adaptive Frequency Hopping (AFH)
- Standard HCI based on SDIO/SPI/UART
- High speed UART HCI, up to 4 Mbps
- BT 4.2 controller and host stack
- Service Discover Protocol (SDP)
- General Access Profile (GAP)
- Security Manage Protocol (SMP)
- Bluetooth Low Energy (BLE)
- ATT/GATT
- HID
- All GATT-based profile supported
- SPP-Like GATT-based profile
- BLE Beacon
- A2DP/AVRCP/SPP, HSP/HFP, RFCOMM
- CVSD and SBC for audio codec
- Bluetooth Piconet and Scatternet
|